| Bench Lathe |
|
- Close grained ground alloyed Cast Iron bed with hardness of
190 - 200 BH.
- Totally enclosed dial type Gear Box with hardened and ground shafts running in
Ball Bearing.
- Spindles and Shafts ground and wearable parts standardized for
interchangeability.
 * Cabinet type Steel Stand & Tray seen above are Optional Accessories Standard Accessories: 1 HP Motor and Switch, 3-Jaw True Chuck (165 mm) with back Plate, 4 - Jaw Dog Chuck (200 mm) with back Plate, Face and Centre Plates, 2 Centres, 2 Pt. traveling guide, threading dial and chart. Optional Accessories: Taper Turning Attachment, Spot Lamp, Cabinet Type Steel Stand with Tray, 3 Point fixed Guide, Motorized Coolant Pump with Tank and fittings. |
|
|
|
|
- All gears hardened - Flame Hardened Bed - Norton Gear Box provides a wide range of feeds and threads in metric and inches
Standard Accessories: Electric Motor, reversible switch, 3 and 4 jaw chuck, coolant pump, machine lamp, 02 nos. dead centre, chuck plate, face plate, steady rest and follow rest. Optional Accessories: Taper turning attachment, revolving centre MT-4
|
|
|
|
- All gears are hardened and ground
Optional Accessories: Taper turning attachment, rear tool post, revolving centre MT-4 |
|
|
|
| - Spindle Cam lock type D1 - 4 Hardened &
Ground - Head stock gears, splines Hardened, Ground and Profile Ground - Head stock Lubricated by a built in Oil pump - Carriage, Surface Slide, Compound Slide & Tail Stock base of 25 Grad Casting, duly Stress Relieved - Taper Wages are of S. G. Iron in Surface slide & Compound slide - Apron Gears are Nitrated and made from EN 8 Material - Feed Box Gears are of EN 24 Material with Toughening Process - Four Position Tool Post with Heat treated Bolts - Tail Stock Spindle Hardened, Ground, Graduated on Outer Diameter with L. C. - End Gear train gears of 25 Graded Casting with bearing type Idler gear - Surface nut with Backlash Eliminator - All Dial Rings Hard chromed and least count Graduated. - Single Grounded Rack and Hardened & Ground Pinion - 2000 RPM in Spindle with two Speed Motor - All Screws made on CNC Turning Centers (Lead screw, Cross Slide screw, Compound Slide screw, Tail Stock screw) - Spindle instant stop electro plugging brake |
 Model: 175 / 750 |
 Model: 215 / 1000 |
| Model: | 175 | 215 | 250 | 254 | |
| Capacity | Height of Centre (mm): | 175 | 215 | 250 | 254 |
| Swing over Bed (mm): | 340 | 420 | 500 | 490 | |
| Swing over Cross Slide (mm): | 176 | 250 | 290 | 300 | |
| Distance Between Centres (mm): | 750 / 1000 | 1000 / 1500 | 1000 / 1500 | 1000 / 1500 / 2000 / 2500 / 3000 | |
| Max. Swing in Gap (mm): | 620 | 700 | 770 | 800 | |
| Bed | Bed Type: | 2V & 2 Flat | 2V & 2 Flat | 2V & 2 Flat | 2V & 2 Flat |
| Bed Width (mm): | 280 | 280 | 355 | 325 | |
| Length of Gap in front of Face Plate (mm): | 160 | 160 | 240 | 175 | |
| Headstock | Number of Spindle Speeds: | 8 | 8 | 18 | 8 |
| Spindle Speeds Range (rpm): | 54 to 1200 | 54 to 1200 | 32 to 1650 | 30 to 1230 | |
| Type and Size of Spindle Nose: | Cam lock size D1- 4 | Cam lock size D1- 4 | Cam lock size 6 | Cam lock size 6 | |
| Spindle Bore (mm): | 40 | 40 | 55 | 52 | |
| Spindle Morse Taper Number: | MT-5 | MT-5 | MT-6 | MT-6 | |
| Diameter of Front Bearing (mm): | 110 x 60 | 110 x 60 | 150 x 85 | 140 x 80 | |
| Tailstock | Spindle Diameter (mm): | 50.8 | 50.8 | 57.15 | 57.15 |
| Spindle Morse Taper Number: | MT-3 | MT-3 | 4 | 4 | |
| Spindle Travel (mm): | 175 | 175 | 200 | 200 | |
| Lateral Movement of Tailstock (mm): | 5 | 5 | 5 | 5 | |
| Saddle | Cross-slide Travel (mm): | 225 | 225 | 325 | 325 |
| Cross-slide Dimensions (mm): | 178 x 415 | 178 x 415 | 550 x 200 | 445 x 200 | |
| Compound Slide Traverse (mm): | 130 | 130 | 150 | 150 | |
| Saddle Traverse (mm): | 640 / 890 | 890 / 1390 | 890 / 1390 | -- | |
| Tool Shank Section (mm): | 22 x 22 | 25 x 25 | 25 x 25 | 25 x 25 | |
| Feeds and Threads | Number of Feeds: | 72 | 76 | 76 | 72 |
| Range of Longitudinal Feeds (mm/rev.): | 0.033 to 0.468 | 0.026 to 0.936 | 0.45 to 1.600 | 0.45 to 1.600 | |
| Range of Cross Feeds (mm / rev.): | 0.021 to 0.301 | 0.016 to 0.620 | 0.003 to 0.128 | 0.003 to 0.128 | |
| Number of Threads: | 103 | 106 | 106 | 103 | |
| Metric Range (number): | 0.2 to 6.5 mm (31) | 0.2 to 7.0 mm (33) | 0.2 to 7.0 mm (33) | 0.2 to 6.5 mm (31) | |
| Inch Range (number): | 72 to 4 TPI (36) | 72 to 4 TPI (36) | 72 to 4 TPI (36) | 72 to 4 TPI (36) | |
| D.P. Range (number): | 44 to 8 DP (21) | 44 to 8 DP (21) | 44 to 8 DP (21) | 44 to 8 DP (21) | |
| Module Range (number): | 0.4 - 3.0 MOD (15) | 0.3 - 3.0 MOD (16) | 0.3 - 3.0 MOD (16) | 0.4 - 3.0 MOD (15) | |
| Lead Screw Diameter (mm): | 31.75 | 31.75 | 31.75 | 38.1 | |
| Lead Screw Pitch (mm): | 6 | 6 | 6 | 6 | |
| Electricals | Main Motor (kW): | 1.5 | 2.25 | 3.75 | 2.25 |
 Model: 250 / 1500 |
|
Approximate Dimensions:
| Model | Net Weight (kgs) | Gross Weight (kgs) | Case Dimensions (m) | Shipping Volume (m3) |
| 175 / 750 | 800 | 1000 | 2.1 x 1.0 x 1.3 | 2.70 |
| 175 / 1000 | 1000 | 1200 | 2.3 x 1.0 x 1.3 | 3.00 |
| 215 / 1000 | 1200 | 1400 | 2.3 x 1.0 x 1.5 | 3.50 |
| 215 / 1500 | 1300 | 1500 | 3.0 x 1.0 x 1.5 | 4.50 |
| 250 / 1000 | 1500 | 1700 | 2.8 x 1.0 x 1.5 | 4.20 |
| 250 / 1500 | 1800 | 2100 | 3.3 x 1.0 x 1.5 | 5.00 |
| 254 / 1000 | 1500 | 1775 | 2.7 x 1.1 x 1.4 | 4.20 |
| 254 / 1500 | 1850 | 2150 | 3.2 x 1.1 x 1.5 | 5.30 |
| 254 / 2000 | 2250 | 2550 | 3.8 x 1.1 x 1.5 | 6.30 |
| 254 / 2500 | 2400 | 2800 | 4.3 x 1.1 x 1.5 | 7.10 |
| 254 / 3000 | 2550 | 2900 | 4.8 x 1.1 x 1.5 | 8.00 |
Standard Accessories: Four Position Tool Post, Toolpost Spanner, Chuck Plate, Face
Plate, Centre Adapter, 2 x Dead Centres, Electric Motor with Electrical Controls, Thread
Dial Indicator, Steady Rest, Follow Rest, Chip Tray, 3 & 4 Jaw Chucks, Coolant Pump,
Machine Lamp
With model 175, 215 & 250 only: Carrier Plate, Rear Splash Guard &
Mechanical Brake
Optional Accessories: Quick Change Tool Post, Taper Turning Attachment, Rear Tool
Post, Keyway cutting attachment, Tool Post Grinder with 8" Grinding Wheel and
electricals
With Model 254 only: 12" Centre Height in lieu of the standard
|
|
|
- Geared Head Heavy Duty Lathe with Norton Gearbox
|
 Model: GH-16 with Planner type stand |
|
Standard Accessories: Face plate, Drive plate,
Steady rest, Follow rest, Thread dial indicator, 4-way tool post, one M.T. centre, 3 and 4
Jaw chuck, suitable motor with control panel, coolant pump and machine lamp.
Optional Accessories: Taper Turning
Attachment (Can be supplied only if ordered with the Lathe)
|
|
|
Standard Accessories: Collet attachment with one Collet, Three step Spindle Pulley bar feed, Toolbox, 2 HP Motor and Reversible Switch Optional Accessories: Norton Gearbox, Feed for Turret Slide, Panel Board |
||||||||||||||||||||||||||||||||
|
Standard Accessories: Collet attachment with one Collet, Toolbox, 2 HP Motor and Reversible Switch and Coolant Pump Optional Accessories: Full Norton Gearbox with Self Shaft, Feed for Turret Slide, Pipe Bar Feed attachment, Panel Board |
|
||||||||||||||||||||||||||||||||
|
Standard Accessories: Collet attachment with one Collet, Toolbox, 3 HP Motor, Panel Board, Pipe Bar feed Attachment, Automatic Feed for Cross Slide and Turret Slide by Self Shaft and Coolant Pump |
|
|
- Ideally suitable for economical production of precision
turned parts.
- Wide range of materials like plastics, aluminium, free cutting steel, brass, etc.
can be machined.
- Cross slide rest with front and rear sildes is included in the basic machine.
- Tail stock is placed on the guide shafts and can be moved to and fro in the
longitudinal direction. The feed motion is controlled by a drum cam.
-Longitudinal turning attachment front can be optionally supplied for components
which can not be produced by plunge cutting. This attachment is mounted on cross slides.
The sliding movement of this attachment is controlled by a drum cam on the cam shaft. The
radial motion is performed by a two pin lever. Thus stepped longitudinal operations can be
made by utilizing two separate setting possibilities of the two cross movement or holding
cams. Taper turning can also be done.
 Model: D-25 |
|
Standard Accessories: Complete electrical equipment, bar feeding attachment, bar feed pipe, double vertical slide, single open tool holder front & rear, automatic electric shutter and a set of service tools
Optional Accessories: Longitudinal Turning Attachment front, step turning tool holder, Collets - metric round (range 4 to 25 mm in steps of 0.5 mm), Drill Collets - metric (range 3 to 13 mm in steps of 0.5 mm)
|
TO OUR PAGE ON MACHINE TOOLS |
|
 |
Maneklal and Sons (Exports) |
|
